A progressive approach to predict shot peening process parameters for forming integral panel of Al7050-T7451

In this paper, a progressive approach to predict the multiple shot peening process parameters for complex integral panel is proposed. Firstly, the invariable parameters in the forming process including shot size, mass flow, peening distance and peening angle are determined according to the empirical and machine type. Then, the optimal value of air pressure for the whole shot peening is selected by the experimental data. Finally, the feeding speed for every shot peening path is predicted by regression equation. The integral panel part with thickness from 2 mm to 5 mm and curvature radius from 3200 mm to 16000 mm is taken as a research object, and four experiments are conducted. In order to design specimens for acquiring the forming data, one experiment is conducted to compare the curvature radius of the plate and stringer-structural specimens, which were peened along the middle of the two stringers. The most striking finding of this experiment is that the outer shape error range is below 3.9%, so the plate specimens can be used in predicting feeding speed of the integral panel. The second experiment is performed and results show that when the coverage reaches the limit of 80%, the minimum feeding speed is 50 mm/s. By this feeding speed, the forming curvature radius of the specimens with different thickness from the third experiment is measured and compared with the research object, and the optimal air pressure is 0.15 MPa. Then, the plate specimens with thickness from 2 mm to 5 mm are peened in the fourth experiment, and the measured curvature radius data are used to calculate the feeding speed of different shot peening path by regressive analysis method. The algorithm is validated by forming a test part and the average deviation is 0.496 mm. It is shown that the approach can realize the forming of the integral panel precisely.     

星载激光通信终端在轨机动对温度影响

对激光通信终端在轨瞬态温度变化开展了仿真，以期研究在轨机动的影响、热分析和热试验时机动模式的简化模拟。通过合理地分析与简化，建立终端的轨道热分析模型，准确模拟在轨机动，根据典型机动模式、外热流和涂层退化等因素设计了计算工况，得出了终端在轨运行过程中的温度场随时间和姿态变化规律。结果表明：不同机动模式下的温度变化存在差异，最大可达23.0℃，采用固定姿态或一维转动的简化热分析或热试验不能准确模拟实际飞行温度，甚至不能部分替代二维转动热分析或热试验；光学天线和反射镜的温度控制是制约终端工作的瓶颈，为终端设计合适的避光机动策略，可大幅度提高温度稳定度和均匀度。研究结果可以为光机电设备在轨机动策略的设计和改进提供参考。     

导流锥结构参数对燃气弹射筒内压力冲击平滑效果影响研究

针对导流锥结构参数对内弹道流场耦合影响问题，基于动态分层动网格技术，构建了含导弹运动和二次燃烧的内弹道数值模型，并验证了模型可靠性。解耦分析了导流锥半径、高度及冲击高度对内弹道流场特性和载荷的影响。结果表明：导流锥的结构直接决定燃气飞溅现象的产生和流场结构的紊乱程度，导流锥的半径、高度和冲击高度的改变会对燃气反射点的位置、二次燃烧的区域以及剧烈程度产生影响;结构优化后的导流锥，较大程度地缓解了冲击现象，获得了较好的平滑效果，筒底压力较实验装置降低了24.5%。     

夹杂物特征参数对拉伸载荷下超高强度钢裂纹萌生与扩展的影响

采用扫描电镜原位观测的方法,动态跟踪观察拉伸载荷作用下航空发动机轴类超高强度钢MA250中不同形状和尺寸的TiN夹杂导致裂纹萌生与扩展的微观行为,从微观角度分析拉伸载荷作用下夹杂物的几何长轴与外加载荷方向成不同角度时裂纹的萌生方式.同时讨论TiN夹杂中第一条裂纹萌生所需的应力与夹杂物面积的关系.结果表明,夹杂物面积越大,第一条裂纹萌生所需的应力越小.     

普郎克定律的一个新推论

根据热辐射基本定律———普郎克定律,推导出了一个新的推论。即对于任意温度T的黑体辐射源,总存在一对应波长λδ,该波长对应的黑体单色辐射亮度对温度T的偏导数最大,且λδT =2 4 10 .3μm·K。这一结论对于单波长辐射温度计设计中探测器波段的选择有重要参考价值,根据此结论可以推出温度测量灵敏度最高的波长。     

NTC技术在微动同步器标度因数的温度补偿中的应用

了微动同步器结构原理，用数学方法找出了温度对其标度因数产生影响的主要原因，温度对激磁线圈的铜阻有影响，从而最终将影响输出电压的大小，针对这一主要原因，采用ＮＴＣ物理方法进行补偿，取得了很好的实际效果。     

一种新型的微机补偿晶体振荡器及开发系统

提出了一种新型的以微处理器为核心的AT切温度补偿晶体振荡器 (MCXO)的设计思想 ,说明了其开发系统的原理 ,给出了最后的实验结果。使用该开发系统得到的这种振荡器可以工作在 - 40℃～ 85℃的环境内 ,频率—温度稳定性≤± 5× 10 - 7。     

Ionospheric behavior of the F2 peak parameters foF2 and hmF2 at Hainan and comparisons with IRI model predictions

Monthly median values of foF2, hmF2 and M(3000)F2 parameters, with hourly time interval resolution for the diurnal variation, obtained with DPS-4 digisonde observations at Hainan (19.4°N, 109.0°E) are used to study the low latitude ionospheric variation behavior. The observational results are compared with the International Reference Ionospheric Model (IRI) predictions. The time period coverage of the data used for the present study is from March 2002 to February 2005. Our present study showed that: (1) In general, IRI predictions using CCIR and URSI coefficients follow well the diurnal and seasonal variation patterns of the experimental values of foF2. However, CCIR foF2 and URSI foF2 IRI predictions systematically underestimate the observed results during most time period of the day, with the percentage difference ΔfoF2 (%) values changing between about −5% and −25%, whereas for a few hours around pre-sunrise, the IRI predictions generally overestimate the observational ones with ΔfoF2 (%) sometimes reaching as large as ∼30%. The agreement between the IRI results and the observational ones is better for the year 2002 than for the other years. The best agreement between the IRI results and the observational ones is obtained in summer when using URSI coefficients, with the seasonal average values of ΔfoF2 (%) being within the limits of ±10%. (2) In general, the IRI predicted hmF2 values using CCIR M(3000)F2 option shows a poor agreement with the observational results. However, when using the measured M(3000)F2 as input, the diurnal variation pattern of hmF2 given by IRI2001 has a much better agreement with the observational one with the detailed fine structures including the pre-sunrise and post-sunset peaks reproduced reasonably well. The agreement between the IRI predicted hmF2 values using CCIR M(30,000)F2 option and the observational ones is worst for the afternoon to post-midnight hours for the high solar activity year 2002. During daytime hours the agreement between the hmF2 values obtained with CCIR M(30,000)F2 option and the observational ones is best for summer season. The discrepancy between the observational hmF2 and that obtained with CCIR M(30,000)F2 option stem from the CCIR M(3000)F2 model, which does not produce the small scale structures observed in the measured M(3000)F2.     

无味卡尔曼滤波在热平衡试验中的应用研究

在航天器热平衡试验中应用温度外推预报技术可以快速准确的给出航天器的极限热平衡温度，缩短热平衡试验时间，降低航天器的研制成本。介绍了一种新颖的热平衡试验数据外推方法——无味卡尔曼滤波(UKF)，分析了UKF的应用效果，结果表明应用UKF外推能够在较短的时间内更准确的获得航天器的极限热平衡温度。     

8mm辐射计特性参数测试及定标

文中简介了小口径天线毫米波辐射计定标系统的设计原理、结构、输出亮温的计算模型 ,研究了从液氮温度到室温范围内进行多点定标的方法 ,并对 8mm辐射计进行了特性参数测试及定标实验 ,得出了微波辐射计的定标方程和灵敏度、线性度、稳定度以及积分时间等指标。在该系统上按给定的程序进行定标 ,精度为 1 .0 6K。